A) Replace the monitor. B) Ensure the RAM modules are properly seated. C) Reconnect the printer. D) Update the operating system.
A) The mouse is defective. B) The CPU cooling system is improperly installed. C) The monitor resolution is too high. D) The keyboard layout is incorrect.
A) The audio jack. B) The SATA data and power cable connections. C) The USB mouse. D) The monitor cable.
A) Apply more thermal paste. B) Align the processor correctly before installation. C) Tighten the heat sink screws first. D) Install the RAM first.
A) Replace the processor. B) Install more RAM. C) Check that the motherboard front-panel USB headers are correctly connected. D) Format the hard drive.
A) Expansion slot B) Heat sink C) RAM D) Power Supply Unit (PSU)
A) Speaker B) Scanner C) Projector D) Monitor
A) VGA port B) HDMI port C) 3.5 mm audio jack D) RJ-45 Ethernet port
A) Work on a carpeted floor. B) Leave the power cord plugged in. C) Touch the CPU pins frequently. D) Wear an anti-static wrist strap.
A) Inspect all cable connections and ensure no loose screws remain inside the case. B) Remove the RAM. C) Disconnect the monitor. D) Unplug the power supply.
A) RAM module B) Motherboard firmware chip C) Hard disk drive D) Graphics card
A) Power supply B) Optical drive C) Hard disk drive D) Processor (CPU)
A) Thermal paste B) Silicone glue C) Adhesive tape D) Lubricating oil
A) To reduce power consumption B) To increase processor speed C) To prevent damage and ensure proper seating D) To improve graphics performance
A) Hard disk drive B) CMOS battery C) Optical drive D) RAM
A) The retaining clips lock into place automatically B) The RAM tilts to one side C) The clips remain open D) The module can still move freely
A) SATA data cable B) Audio header C) IDE ribbon cable D) 24-pin ATX power connector
A) 4-pin or 8-pin CPU power connector B) SATA power connector C) USB header D) Molex connector
A) To provide electrical power to the motherboard B) To transfer data between the motherboard and storage device C) To connect the monitor D) To cool the processor
A) Hard disk drive or SSD B) Heat sink C) RAM module D) Processor
A) All components and cables are securely connected B) The monitor is turned on C) The printer is connected D) The keyboard lights are working
A) Speaker B) Keyboard C) Monitor D) Mouse
A) Monitor B) Printer C) Projector D) Keyboard
A) PS/2 cable B) RJ-11 cable C) SATA cable D) HDMI cable
A) Audio jack B) USB connector C) VGA connector D) SATA connector
A) Projector B) Printer C) Scanner D) Webcam
A) Verify that the 24-pin ATX and CPU power connectors are securely attached. B) Replace the monitor immediately. C) Disconnect the RAM modules. D) Install another operating system.
A) Apply more force until it fits. B) Remove the processor and check the alignment marks before reinstalling. C) Remove the heat sink permanently. D) Bend the socket pins slightly.
A) Replace the hard drive. B) Remove the CMOS battery. C) Ensure the monitor cable is securely connected to the correct video port. D) Disconnect the keyboard.
A) The monitor brightness is too high. B) The printer is turned off. C) The keyboard is unplugged. D) The CPU heat sink or cooling fan was not installed correctly.
A) To improve the appearance of the technician B) To increase the computer's processing speed C) To protect the technician from possible hazards while working D) To speed up computer assembly
A) Gloves B) Apron C) Face mask D) Goggles
A) Rubber-soled shoes B) Sandals C) Canvas shoes D) Leather shoes
A) Replace the processor. B) Remove the motherboard. C) Install the RAM. D) Disconnect the computer from AC power and all peripherals.
A) The computer will immediately shut down. B) Oils and static electricity from the hands may damage the components. C) The BIOS settings will be erased. D) The components become heavier.
A) Graphics card B) A UL-approved surge protector or UPS C) External hard drive D) Optical drive
A) Flow of electricity through power cables B) Discharge of electricity between two objects with different electrical potential C) Electricity produced by batteries only D) Electrical energy stored inside the processor
A) Disconnecting the power supply B) Holding the chassis before touching components C) Eating, drinking, or smoking D) Wearing an anti-static wrist strap
A) To increase processor speed automatically B) To reduce the price of the hardware C) To verify compatibility with the computer system D) To prevent the operating system from updating
A) Color of the computer case B) RAM capacity C) Graphics card D) Processor speed
A) Processor speed B) RAM size C) Optical drive speed D) Hard drive capacity
A) RAM capacity B) Keyboard layout C) Monitor size D) Mouse type
A) SCSI B) SATA C) PS/2 D) IDE
A) Unplug all cables connected to the computer. B) Remove the motherboard. C) Detach the hard drive. D) Remove the CPU fan.
A) Remove the RAM. B) Remove the graphics card. C) Install the processor. D) Open the outer shell or computer case.
A) The processor power connector B) The ATX connector C) The system fan power connector D) The SATA cable
A) Beside the power supply B) Behind the optical drive C) Under the hard drive D) On top of the CPU heat sink
A) Hard drive B) Monitor cable C) Power cord D) Keyboard
A) Unscrew the RAM from the motherboard. B) Pull the module upward without releasing the clips. C) Push down both retaining clips before lifting the module. D) Disconnect the SATA cable.
A) To increase the speed of disassembly. B) To prevent them from getting lost and to make reassembly easier. C) To protect the processor from dust. D) To improve airflow inside the computer. |