AIC JSS 1 3rd Term Exam 2022/23 - Basic Technology
  • 1. The process of providing a quick representation of an object through drawing without the aid of drawing instruments is ------
A) Constructions
B) Right hand sketching
C) Left hand sketching
D) Freehand sketching
  • 2. Where is the title-block located on the drawing sheet?
A) Upper right corner
B) Bottom right hand corner
C) Bottom left corner
D) Upper right hand corner
  • 3. Which of these is a type of drawing board.
A) Full Imperial size
B) Medium size
C) Quarter size
D) Small size
  • 4. A protractor is used for measuring ------
A) Circles
B) Angles
C) Curves
D) Lines
  • 5. Compass is used to draw ------
A) Curves
B) Inclined lines
C) Circles
D) Straight lines
  • 6. In the workshop, accidents are caused by one of the following:
A) Good rules
B) Good observation
C) Carelessness
D) Good working habits
  • 7. All of these can cause fire outbreak except ;
A) Chemicals
B) Fire extinguisher
C) Naked flames
D) Electric spark
  • 8. An unexpected event which can cause harm or injury in the workshop is called;
A) Road accident
B) Safety
C) Failure
D) Workshop accident
  • 9. ATM used in banks for financial transactions is referred to as;
A) Automation Teller Machining
B) Automating Teller Mathods
C) Automated Teller Machine
D) Automated Teller Medicine
  • 10. Shiny or good lustre property is often associated with --------
A) Woods
B) Metals
C) Ceramics
D) Plastics
  • 11. The type of plastics that can be easily softened and remoulded is called ---------
A) Thermolatex
B) Thermoset
C) Synthetic
D) Thermoplastic
  • 12. What is the function of a try square?
A) Measuring lengths
B) Measuring angles
C) Leveling surfaces
D) Marking out right angles
  • 13. Which tool is used to measure the thickness of materials?
A) Feeler gauge
B) Vernier caliper
C) Bevel gauge
D) Protractor
  • 14. Which tool is used to mark a line parallel to an edge?
A) Dividers
B) Scriber
C) Marking gauge
D) Sliding bevel
  • 15. Which tool is used to mark circles and arcs?
A) Bevel gauge
B) Ruler
C) Compass
D) Square
  • 16. What is the purpose of a marking knife?
A) Marking lines on wood
B) Cutting wood
C) Boring holes
D) Measuring lengths
  • 17. Which tool is used to strike or drive nails into wood?
A) Screwdriver
B) Pliers
C) Hammer
D) Chisel
  • 18. Which tool is used for both driving and removing screws?
A) Wrench
B) Allen key
C) Screwdriver
D) Pliers
  • 19. What is the function of a mallet?
A) Cutting wood
B) Drilling holes
C) Holding materials in place
D) Hammering without damaging the work surface
  • 20. Which tool is used to make round holes in wood?
A) Chisel
B) Auger bit
C) Hammer
D) Screwdriver
  • 21. What is the purpose of a brace and bit?
A) Holding workpieces in place
B) Marking out right angles
C) Boring holes
D) Measuring angles
  • 22. Which tool is used to enlarge an existing hole?
A) Mallet
B) Reamer
C) Screwdriver
D) File
  • 23. What is the function of a bench vise?
A) Cutting wood
B) Holding workpieces securely
C) Measuring angles
D) Boring holes
  • 24. Which device is used to hold a workpiece at a specific angle?
A) Mallet
B) Clamp
C) V-block
D) Compass
  • 25. What is the purpose of a sawhorse?
A) Measuring lengths
B) Boring holes
C) Supporting workpieces
D) Cutting wood
  • 26. Which tool is used to cut curves in wood?
A) Chisel
B) File
C) Plane
D) Saw
  • 27. What is the function of a coping saw?
A) Cutting curves and intricate shapes
B) Drilling holes
C) Boring holes
D) Cutting straight lines
  • 28. What is the definition of work in the context of physics?
A) The transfer of energy from one object to another
B) The amount of force applied to an object
C) The displacement of an object due to a force acting on it
D) The speed at which an object moves
  • 29. Which of the following is a renewable source of energy?
A) Natural gas
B) Solar power
C) Coal
D) Petroleum
  • 30. What is the SI unit of energy?
A) Volt
B) Ohm
C) Watt
D) Joule
Created with That Quiz — where test making and test taking are made easy for math and other subject areas.