A) Rulers B) Tape Measure C) L-square D) Sewing Gauge
A) I and IV only B) I, II III, and IV C) I, II, and III only D) I, II, and IV only
A) I, and II only B) I, and III only C) I, II III, and IV D) I and IV only
A) It is used for trimmings, clipping threads, and snipping slashes B) It is used to snip threads, and they are not designed to cut fabric C) This is popular in zigzagging or scalloped edge or for seam finishes. D) It is used in working with fine details in delicate fabrics and in embroidery work.
A) Start from the top of the shoulder over bust down to natural waistline. B) Start from the top of the shoulder to the natural waistline. C) Start from the tip of the shoulder down to the center of the bust (nipple). D) Start from the nape of neck down to natural waist.
A) Upper Bust, Lower Bust, Waist, Sleeve Hol B) Bust to Bust, Shoulder to Bust, Upper Bust, Full Back C) Bust to Bust, Shoulder to Shoulder, Across Back, Full Back D) Shoulder to Bust, Back Shoulder to Waist, Down Center Back
A) Circumferential, Vertical, Parallel Measurements B) Circumferential, Vertical, Rectangular Measurements C) Horizontal, Vertical, Circumferential Measurements D) Horizontal, Vertical, Parallel Measurements
A) The garment will not fit perfectly the client. B) The garment will be accepted by the client without a problem. C) The garment will need minor or little alterations. D) The garment will fit perfectly the client.
A) To be able to create the best style for the garment. B) To be able to choose proper print of fabric as well as color combinations. C) To be able to produce a garment that is inferior and of poor quality. D) To be able to produce a garment that fits perfectly with the client.
A) C.Take the measuring tape around the waistline. B) A.Start around the smallest part of the waistline then insert two (2) fingers under the measuring tape for allowance. C) B.Start around the fullest part of the hip/buttocks with two (2) fingers inserted under the measuring tape. D) D.Taken around the fullest part of the bottom.
A) 10/2.54 B) 10-2.54 C) 10+2.54 D) 10x2.54
A) 73.5cm B) 63 cm C) 63.5cm D) 83.5
A) Php1,425 B) Php 1,245 C) Php 2,524 D) Php 1,524
A) Php1,425 B) Php 1,245 C) Php 1,524 D) Php 2,524
A) (80)-2.54 B) 80/ 2.54= C) 80 X 2.54= D) 2.54/ 80=
A) Union B) Division C) Subtraction D) Multiplication
A) ½ B) 3/8 C) ¼ D) 1/8
A) 3/8 B) 1/8 C) ¼ D) ½
A) 4 B) 3 C) 6 D) 5
A) minus B) median C) mode D) measure
A) Regularly oil the moving parts and clean the lint from the machine. B) Only clean it when it looks dirty. C) Use it continuously without any breaks. D) Store it in a damp place to keep it from rusting.
A) Because it is specially made to avoid damaging the machine parts B) Because it dries faster than cooking oil C) Because it is cheaper than other oils D) Because it gives a pleasant smell while sewing
A) To keep it safe from theft B) To make it look more presentable in the sewing room C) To protect it from dust and dirt that may affect its function D) To prevent children from playing with it
A) To confirm that the machine belt is tight B) To test if the machine motor is working properly C) To ensure the needle is sharp and not bent, preventing fabric damage D) To see if the presser foot is aligned correctly
A) Clean and re-thread the machine properly B) Adjust the height of the sewing table C) Replace the motor immediately D) Oil the presser foot lever
A) Tighten the tension discs B) Replace the needle with a new one C) Cover the machine with a dust cover D) Apply a small amount of sewing machine oil to the moving parts
A) Clean the bobbin case with a cloth B) Replace the needle with the correct size for the fabric C) Oil the balance wheel D) Tighten the table screws
A) Chain stitch B) Basting stitch C) Backstitch D) Overcast stitch
A) Tape measure B) Ruler C) L-square D) Tracing wheel
A) Dressmaker’s carbon paper and tracing wheel B) Needle threader and scissors C) Tailor’s chalk and sewing machine D) Ruler and tape measure
A) Needles B) Tape measure C) Pins and pincushion D) Tracing wheel
A) Thimble B) Pinking shears C) Seam ripper D) L-square
A) Correct, because it saves money from buying shears B) Good choice, because kitchen scissors are stronger C) Acceptable, because any scissors can cut fabric D) Wrong, because kitchen scissors may damage the fabric and dull quickly
A) Correct, because the pen is always available B) Acceptable, because the marks are easy to see C) Good practice, because pens are cheaper than chalk D) Incorrect, because pen marks may stain the fabric permanently
A) L-square B) Dressmaker’s shears C) Gauge D) Tape measure
A) The size of the sewing room B) The color of the student’s outfit C) Price of the sewing machine D) Type of marking needed on the fabric
A) Marking B) Cutting C) Measuring D) Holding or securing fabric
A) Tape measure B) Ruler C) L-square D) French curve
A) Cause: Dust in shuttle → Remedy: Oil the feed dog B) Cause: Loose presser foot → Remedy: Tighten it C) Cause: Incorrect threading → Remedy: Re-thread the machine properly D) Cause: Wrong fabric → Remedy: Replace with thinner fabric
A) Cause: Lack of oil → Remedy: Lubricate moving parts B) Cause: Dull needle → Remedy: Change presser foot C) Cause: Wrong bobbin size → Remedy: Adjust stitch length D) Cause: Loose screw → Remedy: Apply chalk
A) Cause: Thread color mismatch → Remedy: Change to matching thread B) Cause: Incorrect thread tension → Remedy: Adjust upper thread tension C) Cause: Presser foot dirty → Remedy: Clean presser foot D) Cause: Needle too sharp → Remedy: Replace with blunt needle
A) Cause: Wrong bobbin → Remedy: Wind bobbin again B) Cause: Wrong presser foot → Remedy: Replace thread C) Cause: Forcing fabric while sewing → Remedy: Let the feed dog move the fabric naturally D) Cause: Loose belt → Remedy: Tighten screw
A) Cause: Presser foot wrong → Remedy: Clean feed dog B) Cause: Machine old → Remedy: Buy a new machine C) Cause: Loose tension → Remedy: Adjust upper thread tension correctly D) Cause: Fabric too thin → Remedy: Use thick fabric only
A) Replace the presser foot lever B) Ensure the needle is straight and the correct size for the fabric C) Oil the balance wheel D) Use tailor’s chalk for fabric marking
A) Replace the presser foot screw B) Change the bobbin case immediately C) Raise and clean the feed dog to ensure smooth fabric movement D) Re-thread the upper thread |