A) Voltages and currents at all places within the circuit B) Only voltages at specific nodes C) Power consumption and frequency D) Resistance and capacitance values only
A) Using piecewise-linear approximation B) Using Gaussian elimination only C) Using complex number theory D) Using hydraulic analogies
A) Specialized computer programs B) Circuit prototypes C) Manual calculations D) Continuity tests
A) GNUCAP B) HSPICE C) Simulink D) SapWin
A) C++ and Python B) Java and SQL C) HTML and XML D) VHDL-AMS and verilog-AMS
A) Avoiding time, cost and risk of error B) Eliminating the need for software C) Increasing circuit voltage limits D) Simplifying network topology
A) SapWin B) SPICE or GNUCAP C) HSPICE D) PLECS
A) GNUCAP B) SPICE C) HSPICE D) SapWin
A) A steady state solution B) A piecewise-linear model C) A prototype filter D) A small-signal estimate
A) Kirchhoff's current law B) Ohm's Law C) Superposition theorem D) Maxwell's analogy
A) The operating points of each element B) The continuity test results C) The netlist representation D) The hydraulic analogy
A) It can be treated as a battery B) It can be replaced with a diode C) It can be linearized around its operation point D) It can be removed from the circuit
A) A linear circuit matrix B) An AC power analysis C) A hydraulic model D) A schematic diagram
A) Ohm's Law B) Kirchhoff's current law C) Firestone analogy D) Trent analogy
A) With a prototype filter B) With a continuity test C) With a network analyzer D) With Gaussian elimination
A) HSPICE B) GNUCAP C) SapWin D) PLECS interface to Simulink
A) As an hydraulic system B) As a completely linear network of ideal diodes C) As a collection of AC power sources D) As a non-linear matrix of transistors
A) When the steady state solution is found B) Every time a diode switches from on to off or vice versa C) Every time the voltage reaches zero D) During Gaussian elimination
A) It eliminates the need for diodes B) It increases the accuracy of the simulation, but also increases its running time C) It decreases the simulation time and increases accuracy D) It simplifies the linear circuit matrix
A) Circuit diagram B) Mesh analysis C) Bridge circuit D) Continuity test
A) Superposition theorem B) Potential divider C) Impedance analogy D) Schematic
A) RC circuit B) Topology C) Network analyzer D) Netlist
A) Superposition theorem B) Circuit diagram C) AC power network analyzer D) Hydraulic analogy
A) Mesh analysis B) Schematic C) Continuity test D) Bridge circuit
A) Active filter B) Passive filter C) Digital filter D) Prototype filter
A) Piecewise-linear approximation B) Topology (electronics) C) Impedance analogy D) HSPICE simulation
A) Digital multimeter B) Network analyzer (electrical) C) Oscilloscope D) Spectrum analyzer
A) Bridge circuit analyzer B) DC power meter C) Network analyzer (AC power) D) Resistive continuity tester
A) Continuity test B) Diode switching test C) Voltage drop test D) Steady state test
A) Firestone analogy B) Hydraulic analogy C) Trent analogy D) Maxwell analogy
A) Firestone analogy B) Maxwell analogy C) Trent analogy D) Hydraulic analogy
A) Firestone analogy B) Maxwell analogy C) Trent analogy D) Mechanical analogy
A) Trent analogy B) Maxwell analogy C) Firestone analogy D) Hydraulic analogy
A) Mechanical–electrical analogies B) Kirchhoff network topologies C) Steady state solutions D) Piecewise-linear models
A) RC circuit B) Potential divider C) Series and parallel circuits D) Bridge circuit
A) RLC circuit B) RC circuit C) LC circuit D) RL circuit
A) RC circuit B) LC circuit C) RL circuit D) Bridge circuit
A) RL circuit B) LC circuit C) Potential divider D) RC circuit
A) RL circuit B) RC circuit C) LC circuit D) RLC circuit
A) Mesh analysis B) Bridge circuit C) Prototype filter D) Potential divider
A) Series and parallel circuits B) Steady state and transient circuits C) Linear and non-linear circuits D) Analog and digital circuits
A) Equal to the total resistance B) Equal to the source voltage C) Zero D) Constant and positive
A) Time-varying networks B) Networks containing nonlinear components C) Networks without any resistors D) Networks containing reactances
A) Voltage and current are completely unrelated B) Resistance changes randomly over time C) Signals are linearly superimposable D) Signals always cancel each other out
A) Lumped elements B) Distributed elements C) Transmission lines D) Active sources
A) The passive-source model B) The DC-response model C) The distributed-element model D) The resistive-network model
A) A semi-lumped design B) A nonlinear electronic circuit C) An ideal voltage network D) A fully saturated circuit |