- 1. 1. The following are major components of lathe machines except ______
A) Carriage
B) Headstock
C) Wool
D) Tailstock
- 2. 2. Which of the following is not in the category of operations that are commonly performed on the lathe machines?
A) Steaming
B) Facing
C) Turning
D) Cutting
- 3. 3. The operation that is used to produce flat surfaces on lathe machines is called ----------
A) Drilling
B) Facing
C) Knurling
D) Turning
- 4. 4. An operation which involves cutting threads on a workpiece is known as --------
A) Deep cutting
B) Screw cutting
C) Pain cutting
D) Lateral cutting
- 5. 5. Which of the following machines is most suitable for marking holes in a workpiece?
A) Drill press
B) Air press
C) Forge press
D) Mill press
- 6. 6. The following are types of grinding machines except ----------
A) Plain grinder
B) Surface grinder
C) Belt grinder
D) Bench grinder
- 7. 7. The coolant which helps to reduce distortion, power consumption, improve surface finish and protects against corrosion of the workpiece is called ----
A) Milling gas
B) Sprinkler fluids
C) Cutting fluid
D) Grinding powder
- 8. 8. The machine that can be used to cut workpieces with coarse tooth hacksaw blades is called ------
A) Screw machine
B) Turning machine
C) Power sawing machine
D) Chamfering machine
- 9. 9. Forging can be classified into the following except.....
A) Cloudy forging
B) Hot forging
C) Cold forging
D) Warm forging
- 10. 10. The types of folding machines include the following except -----
A) Buckle folder
B) Knot folder
C) Paper folder
D) Knife folder
- 11. 11. The series of operations that transform industrial materials from a raw material state into a finished product state is called
A) Quarter sawn
B) Feller bunching
C) Material processing
D) Pre-cut
- 12. 12. The key concept of timber processing includes the following except -------
A) Treatability
B) Growth and felling
C) Seasoning
D) Conversion
- 13. 13. One of the following is not a process in timber felling.
A) Bucking
B) Knitting
C) Limbing
D) Skidding
- 14. 14. ------ and ------ are the two methods of timber seasoning
A) Limbing and bucking seasoning
B) Natural and artificial seasoning
C) Limbing and skidding seasoning
D) Plain and quarter seasoning
- 15. 15. In the conversion of timber, the method that produces radial boards and far more expensive than the tangential timber because of the need to double handle the log is known as --------
A) Plain and edge sawn
B) Quarter sawn
C) Curved sawn
D) Through and through sawn
- 16. 16. Drying process that involves the introduction of heat is ------
A) Kiln drying
B) Temperate drying
C) Solar Energy drying
D) Hot drying
- 17. 17. The most common treatment process is known as -----
A) Temperature treatment
B) Deliberate treatment
C) Temple treatment
D) Pressure treatment
- 18. 18. One of the following is not a preservative for timber.
A) Folder treatment
B) Envelope treatment
C) Light organic solvent-borne preservatives
D) waterborne preservatives
- 19. 19. Defects due to insects and other animals include the following except ----------
A) Warping
B) Birds and mammals
C) Marine borer
D) Insects
- 20. 20. One of the following is not a defect due to conversion.
A) Miscut
B) Case hardening
C) Boxed heart
D) Machine notches
|